About

 

How do you feel in relation to Installing A Bathtub?

Mounting a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is readily accessible, the task can relocate quickly; if you have to open a wall surface to get rid of the old tub as well as position the brand-new tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub and also set in the brand-new one. Make sure you have certified on your own for the job and also are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed job, it is better to consider using one before you start. Possibilities are you might require a professional plumber to make tube connections.
This write-up will certainly assist you mount a new bathtub in your washroom if you have actually currently gotten a brand-new tub and don't need to transform the setup of your previous water system pipelines.
Your devices and also product checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Planning for the Installment

Firstly, the supporting framework supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final position.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Mounting the Bathtub

Utilizing both wood boards under its feet, position the tub in the required position. The wood boards are useful in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the tub up until the level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap port to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if needed. Fill up the bathtub and likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub should wait up until the tub has actually been used a minimum of when as this will resolve it into its final position.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Secure the tap in place with the producer provided backnut. As soon as the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the area where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and also installations. They are offered in tubes as well as cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to allow for the movement experienced when the bathtub remains in usage. The sealant can break relatively early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant adhesive and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you enjoyed our section about How to Install a Bathtub. Thanks so much for taking the time to read through our content. Do you know anybody else who is inquisitive about the topic? Take a moment to share it. I cherish reading our article about How to Install a Bathtub Yourself.

Drain issues? Reach out!